Carburettors & Manifolds
![btn_xpressCheckout[1]](/communities/7/004/007/439/697/images/4554186129_pre.jpg)
With the increase in scooter engine power, carburetion has had to improve, after over thirty years of working with Dellorto we can say that we can cover most engine options. We can supply spares for Vespas and carburettor for standard machines or Series 1 and 2 for Lambretta.
A range of PHBL, PHBH, VHSA and VHSC carburettors are available in 24, 25, 26, 28, 30, 32, 34 and 38mm sizes, Flat slide, round slide and power jet options are available.
We also stock an unrivalled quantity of manifold jets, atomiser needles and filters to cover all engine layouts.
We will supply a single jet or a fully set kit to suit your needs, please see the carburettor
for the system to suit your engine.
£10.95
Cable choke kit
£8.95
Flip up choke kit
£1.00
Carburettor rubber clips
Stainless steel, price listed is per clip
£13.99
Float valve PHBH carburettor
Sizes available 200, 250, 300, 350, please state size required in the checkout, if unsure please contact us
£0.50
Needle clip
£59.95
Imola - Monza reed valve complete
£29.95
Imola - Monza reed block
£29.95
Imola - Monza manifold
£6.49
PHBH 26-28-30 mm carburettor rubber
£39.99
PHBH 26-28-30 mm manifold kit
£89.99
PHBH 26 mm carburettor
PHBH 26 mm complete carburettor kit
£175.99
carburettor with cable type choke fitting, manifold, connector rubber, stainless steel fixing clips, inlet gasket, fixing studs nuts & washers, remote filter system, please enter the type & size of cylinder i.e.186 mugello & the exhaust system i.e. Ancilotti 42mm in the checkout & we will jet the carburettor to suit
PHBH 28mm carburettor
£89.99
PHBH 28mm complete carburettor kit
£175.99
carburettor with cable type choke fitting, manifold, connector rubber, stainless steel fixing clips, inlet gasket, fixing studs nuts & washers, remote filter system, please enter the type & size of cylinder i.e.186 mugello & the exhaust system i.e. Ancilotti 42mm in the checkout & we will jet the carburettor to suit
PHBH 30 mm carburettor
£89.99
£149.00
LTH reed valve for 26,28,30 PHBH Dellorto
CNC machined alloy manifold with manifold rubber, fixings,studs, nuts, washers, & all gaskets complete with manifold rubber holding clip & reed block. We first tested in November 09 & were surprised by the results.
-Test 1, Rapido 225cc race, JL3 exhaust, 28mm PHBH carburettor. Low end torque improved and made this machine much more usable at low revs. Fuel consumption was averaging 36.5 mpg. With LTH reed valve fitted consumption was 74mpg! This system reduces spitback, saving expensive fuel and oil waste. Main and pilot jets will need reducing by 10-20 %
-Test 2, Cast iron stage 4 200cc cylinder, JL3 exhaust, 30mm PHBH DellOrto carburettor, power & rideabilty increased throughout the range. No previous mpg figures were available. On test with LTH reed valve fitted average mpg over 400 miles was 73 mpg with hard use.
The LTH reed valve will fit all cast iron barrels 125,150,175 and 200cc, Mugello 186,200 & 225cc. Rapido 200,225 & 250 cc. This is the latest version (as of August 2010)
Please note, you will need to remove part of the cylinder fin forward of the inlet port to allow the manifold to sit properly. This is a very easy modification and will only take about 5 minutes, see last picture.
Please specify the carburettor size in the checkout
PHBH 30mm complete carburettor kit
£175.99
carburettor with cable type choke fitting, manifold, connector rubber, stainless steel fixing clips, inlet gasket, fixing studs nuts & washers, remote filter system, please enter the type & size of cylinder i.e.186 mugello & the exhaust system i.e. Ancilotti 42mm in the checkout & we will jet the carburettor to suit
FREE!!!
PHBH air filter foam type
£33.99
£39.99
PHBH air filter for imola-monza-ts1
Fits under panel
PHBH air filter mesh type
£29.99
You are viewing the text version of this site.
To view the full version please install the Adobe Flash Player and ensure your web browser has JavaScript enabled.
Need help? check the requirements page.
